CM-E1
- CM-E1 is a low voltage detector of Carbon Monoxide (CO).
- The CM–E1 is designed for connection to UL Listed Fire Alarm/Burglary Control Panels.
- Alarm control panels that work on 12 or 24 VDC can provide battery backup to the CM-E1 detectors.
- This carbon monoxide detector is designed to detect CO gas from ANY source of combustion.
- It is NOT designed to detect smoke, fire or any other gas.
Zalo:
- Kinh Doanh OnlineWhatsApp:
- Tư Vấn Giải PhápFacebook:
- Hỗ Trợ Đơn HàngSales Engineer:
- 0989 544 978Macurco CM-E1 Carbon Monoxide Detector (CO)
The CM-E1 is a low voltage (9-32 VDC) detector of Carbon Monoxide (CO). The CM–E1 is designed for connection to UL Listed Fire Alarm/Burglary Control Panels. NOTE: Any time the words “Control Panel” or “Alarm Panel” or “Alarm Control Panel” are used in these instructions, they refer to a UL Listed Fire Alarm/Burglary Control Panel. Alarm control panels that work on 12 or 24 VDC can provide battery backup to the CM-E1 detectors. This carbon monoxide detector is designed to detect CO gas from ANY source of combustion. It is NOT designed to detect smoke, fire or any other gas.
- Listed to UL standard 2075 for the Standard For Safety for Gas and Vapor Detector and Sensors
- Tested to UL 2075 using UL 2034 Sensitivity limits for carbon monoxide gas.
- Surface mounts to a wall using the supplied enclosure rear housing.
- Flush mounts in a 2 x 4 (1-1/2 inch deep minimum) [5.08 cm x 10.16 cm (3.81 cm deep minimum)] single gang switch, or handy electrical box.
- Small, low profile, attractive unit in a white plastic case.
- Detector alarms at multiple levels of exposure to carbon monoxide based on time weighted averages of the gas present. Inexpensive, easy to install.
- Microcomputer control allows mostly automatic operation.
- Test & Reset switch conducts internal tests and actuates alarm relay. Visual display: GREEN – Normal operation.
- FLASHING AMBER – Trouble Contact your installer or Macurco Tech Support
- RED – Danger! Move to fresh air (hazardous condition is present.) Highly linear electrochemical sensor
- N.O. or N.C. SPST Alarm Relay and N.C. SPST Trouble relay to connect to Alarm Control Panels
- Buzzer: Produces repeating loud tone bursts during alarm, and chirps if sensor trouble is found.
CM-E1 Datasheet
- Voltage: 9-32 VDC
- Current (normal / alarm): 15mA / 35mA @ 9-32V
- Size: 3-1/8 X 5-1/8 X 1-1/2 inch (7.94 x 13.02 x 3.81 cm)
- Alarm Relay: SPST, 100mA, 40VDC
- Trouble Relay: SPST, 100mA, 40VDC
- Buzzer Rating: 85 dBA at 10 Feet
- Shipping Weight: One pound
- Operating Temp. Range: 40°F (4.4°C) to 100°F (37.8°C)
- Alarm Setting: Per UL 2034
- Color: White
- Designed for use with a UL Listed Fire Alarm/Burglary Control Panel
The relay of the CM-E1 is a dry contact and rated at 100mA, 40VDC. It is not suitable for fan control use. When connecting the units to remote buzzers or other devices (all buzzers or “other devices” must be UL approved), make sure that the load does not exceed the relay’s rating. External buzzers must be capable of generating a sound output greater than 85 dBA at 10 ft (3.048 M).
There are no reviews yet.