AIR-WAP602-X1
- AIR-WAP602-X1 802.11ax Wi-Fi 6 wireless in-wall access point
- Wired and wireless gigabit access
- Easy to deploy x86 standard panel
- Downlink Port
- Good PoE compatibility
- Multi-mode: fit, fat, bridge
- Kinh Doanh
Mr Minh:
- Kinh Doanh
Mr Luân:
- Kinh DoanhWhatsApp:
- Tư Vấn Giải PhápFacebook:
- Hỗ Trợ Đơn HàngSales Engineer:
- 0989 544 978Air Pro AIR-WAP602-X1 Wi-Fi 6 Dual Band Enterprise Access Point
AIR-WAP602-X1 is a dual-band high-performance in-wall gigabit wireless access point based on the 802.11ax standard. supports standard 86 panel for easy installation and offers upto 1775Mbps access rate. It works in 2.4GHz and 5GHz frequency bands and supports advanced wireless technologies such as MU-MIMO, OFDMA, spatial multiplexing and TWT. The first radio works in the 2.4GHz frequency band and can provide access rate of upto 575Mbps; the second radio works in the 5GHz frequency band and can provide access rate of upto 1200Mbps.
802.11ax Wi-Fi 6 wireless in-wall access point:
AIR-WAP602-X1 supports the 802.11ax standard, operates in both 2.4 GHz and 5 GHz band, and provides an access rate upto 1775 Mbps. This model is a high-end in-wall access point for hotel, education, government and business networks.
Wired and wireless gigabit access:
AIR-WAP602-X1 integrated gigabit wired uplink port can truly meet the bandwidth requirement of wireless clients.
Easy to deploy x86 standard panel:
AIR-WAP602-X1 panel supports 86 box standard, and can perfectly be installed on any standard panel. With the use of the PoE cable, the whole installation is low cost, silent and quick (the time to install an AP is less than 3 minutes).
Downlink Port:
AIR-WAP602-X1 provides one gigabit downlink port for the accessing of wired devices, which improves the flexibility of networking deployment.
Good PoE compatibility:
AIR-WAP602-X1 can work well with all PoE switches (viz. Cisco, HUAWEI, Juniper, etc.) which support 802.3af/at standard. This allows AIR-WAP602-X1 to power up directly without any power adapter.
Multi-mode: fit, fat, bridge:
AIR-WAP602-X1 can work in fit, fat or bridge mode and can flexibly switch between these three modes according to network planning requirements.
AIR-WAP602-X1 Datasheet
| Model | AIR-WAP602-X1 |
|---|---|
| Dimensions(L*W*D) (mm) | 86 x 86 x 51.8 |
| Uplink-port | 1* 10/100 /1000Base-T (PoE) |
| Downlink port | 1* 10/100 /1000Base-T |
| Power supply | 802.3 at PoE |
| LED indicators | Power |
| Maximum power consumption | <12W |
| Antenna gain | Built-in 2.4 GHz 3 dBi antenna and 5 GHz 3 dBi antenna |
| Working frequency band | 802.11b/g/n/ax: 2.4 GHz to 2.483 GHz 802.11a/n/ac/ac wave 2/ax: 5.150GHz to 5.350GHz; 5.47GHz to 5.725GHz; 5.725GHz to 5.850GHz |
| Modulation technology | 11b : DSS: CCK@5.5/11Mbps, DQPSK@2Mbps, DBPSK@1Mbps 11a/g : OFDM:64QAM@48/54Mbps,16QAM@24Mbps, QPSK@12/18Mbps, BPSK@6/9Mbps 11n : MIMO-OFDM: BPSK, QPSK,16QAM,64QAM 11ac : MIMO-OFDM: BPSK, QPSK,16QAM,64QAM,256QAM 11ax: MIMO-OFDMA: BPSK, QPSK,16QAM,64QAM,256QAM,1024QAM |
| Transmit power | 2.4G: 20dBm 5G : 20dBm (Note : final output power comply with deployment regulation might be different) |
| Power adjustment granularity | 1 dBm |
| Working/Storage temperature | –10°C to +55°C –40°C to +70°C |
| Working/Storage RH | 5% to 95% (non-condensing) |
| Protection level | Ip41 |
| WLAN | Product positioning: In-wall dual-frequency Working frequency band: 2.4GHz and 5GHz Bandwidth performance: 1775Mbps Virtual AP (BSSID): 8 (4 for each radio) Concurrent user: 128 Number of spatial streams: 2.4GHz:2, 5GHz:4 Dynamic channel adjustment (DCA): Yes Transmit power control (TPC): Yes Blind area detection and repair: Yes SSID hiding: Yes RTS/CTS: Yes RF environment scanning: Yes Hybrid acces: s Yes Restriction on the number of access users: Yes Link integrity check: Yes Accessing control of terminals based on signal strength: Yes Forcing terminals to roam based on signal strength: Yes Intelligent control of terminals based on airtime fairness: Yes High-density application optimization: Yes |
| 802.11ax enhancements | Space streams: 2.4GHz:2, 5GHz:2 Frequency band: 2.4GHz + 5GHz 80 MHz bundling: Yes 1200Mbps (PHY:) Yes Frame aggregation (A-MPDU): Yes Frame aggregation (A-MSDU:) Yes Maximum likelihood demodulation (MLD): Yes Transmit beamforming (TxBF): Yes Maximum ratio combining (MRC): Yes Space-time block coding (STBC): Yes Low-density parity-check code (LDPC): Yes |
| Security | Encryption: 64/128 WEP, TKIP, and CCMP encryption 802.11i: Yes Portal authentication: Yes WAPI: Yes MAC address authentication: Yes LDAP authentication: Yes PEAP authentication: Yes WIDS/WIPS: Yes Protection against DoS attacks: Anti-DoS for wireless management packets Forwarding security Frame: Filtering, white list, static blacklist, and dynamic blacklist User isolation: AP L2 forwarding suppression Isolation between client Periodic SSID enabling and disabling: Yes Access control of free resources: Yes Wireless SAVI: Yes ACL: Access control of various data packets such as MAC, IPv4, and IPv6 packets Secure access control of APs: Secure access control of APs, such as MAC authentication, password authentication, or digital certificate authentication between an AP and an AC. Binding SSID with VLAN: Yes 802.11W: Yes, encryption of management frames |
| Forwarding | IP address setting: Static IP address configuration or dynamic DHCP address allocation IPv6 forwarding: Yes IPv6 portal: Yes Local forwarding: Yes Multicast IGMP snooping Roaming: Yes AP switching reference: Signal strength, bit error rate, RSSI, S/N, whether neighboring APs are normally operating, etc. |
| QoS | WMM: Yes Priority mapping: Ethernet port 802.1P identification and marking Mapping from wireless priorities to wired priorities. QoS policy mapping: Mapping of different SSIDs/VLANs to different QoS policies Mapping of data streams that match with different packet fields to different QoS policies. L2-L4 packet filtering and flow classification Yes: MAC, Ipv4, and IPv6 packets. Load balancing: Load balancing based on the number of users; Load balancing based on user traffic: Load balancing based on frequency bands Bandwidth limit: Bandwidth limit based on Aps; Bandwidth limit based on SSIDs; Bandwidth limit based on terminals; Bandwidth limit based on specific data streams. Call admission control (CAC): CAC based on the number of users Power saving mode: Yes Automatic emergency mechanism of APs: Yes Intelligent identification of terminals: Yes Multicast enhancement: Multicast to unicast |
| Management | Network management: Centralized management through an AC; both fit and fat modes Mesh networking: Through central AP to manage the RE AP Maintenance mode: Both local and remote maintenance Log function: Local logs, Syslog, and log file export Alarm: Yes Fault detection: Yes Statistics: Yes Switching between the fat and fit modes: An AP working in fit mode can switch to the fat mode through a wireless AC;; An AP working in fat mode can switch to the fit or bridge mode through a; local control port or Telnet(web); An AP working in bridge mode can switch to the fit or fat mode through a local control port or Telnet(web) Remote probe analysis: Yes Watchdog: Yes |
| Value added service | Value added marketing: Support: various apps based on intelligent terminals, advertising push based on location, personalized push of portals Value added authentication: WeChat, SMS, QR code Passenger flow analysis Yes |
There are no reviews yet.